How To Replace The Screw And Clasp On Your RGS-0 Scooter

How To Replace The Screw And Clasp On Your RGS-0 Toddler Scooter

Step 1: 

Using an Allen key that you can find in the pack of tools that come with your scooter, insert into the bolt in the centre of the front wheel and turn.

Remember, if you're taking off the right wheel you'll have to unscrew anticlockwise. If you're taking off the left wheel you'll have to unscrew clockwise.

 

Step 2:

Take the bolt and the wheel out of the scooter.

 

Step 3:

Repeat this with the other front wheel.

 

Step 4: 

Put two Allen keys in the sides of the front of the scooter into the screws. Hold one Allen key in place while you unscrew the other. Refer to the video for a visual representation.

 

Step 5: 

Take the screw out of the scooter.

 

Step 6: 

Using an Allen key, push the bolt from the inside of the scooter out.

 

Step 7: 

Pull the top half of the scooter up so it's detached.

 

Step 8:

Unscrew the screw from the clasp at the bottom of the scooter.

 

Step 9:

Take the old screw and clasp and the spring out of the scooter.

 

Step 10: 

Insert the new clasp, and the spring into the scooter, exactly the way the original parts were positioned before. 

 

Step 11:

Tighten the screw at the end of the clasp.

 

Step 12: 

Turn the scooter over so you're facing the fender plate. 

 

Step 13: 

Using the pointed side of an Allen key, unscrew the screws on the fender plate.

 

Step 14: 

Using the flat side of an Allen key, unscrew the bolts on the fender plate.

 

Step 15: 

Take the fender plate off from the scooter.

 

Step 16: 

With the new screw and clasp installed, connect the neck of the scooter back with the body.

 

Step 17: 

Making sure the holes at the base of the scooter are lined up, put the handlebar base bolt into the hole. Don't put all the way through yet. 

 

Step 18:

Insert the bolt through the spring, aligning it where the fender plate was removed. The bolt should pass through the loop on the spring and into the corresponding hole in the scooter's neck. For a visual guide, refer to the video. This part is tricky, so take your time! 

 

Step 19: 

Screw the bolt back onto the side of the scooter using an Allen key. 

 

Step 20: 

Using two Allen keys, hold one side in the bolt and tighten the other screw. Refer to the video for a visual guide. 

 

Step 21: 

Place the fender plate back onto the bottom if the scooter. 

 

Step 22: 

Using the flat side of an Allen key, tighten the bolts back onto the fender plate. 

 

Step 23: 

Using the pointed side of an Allen key, tighten the screws back onto the fender plate. 

 

Step 24: 

Place the front wheels back onto the scooter. 

 

Step 25: 

Screw the bolts back onto the wheels using an Allen key. 

Remember, if you're tightening the right wheel you'll have to screw clockwise. If you're tightening the left wheel you'll have to screw anticlockwise.

 

You're all set! Happy Scooting!

 

How to Tighten/Loosen the Screw and Clasp on Your RGS-0 Scooter

 

Is the screw and clasp too loose?

With the scooter facing you, turn the screw on the clasp clockwise until the clasp is stiff enough that the handlebars stay upright. 

Is the clasp on your scooter too tight?

Turn the screw on the clasp anticlockwise until the clasp is able to move, but not so loose the handlebar can't stay upright. 

You're all set! Happy Scooting!

 

 

Within Your Warranty?

Please contact our customer service team who will be more than happy to help assist with any questions you have.

Contact us and we'll give you the part you need for free.

Outside of Your Warranty?

Please visit our parts shop on our website where we sell a range of parts at a low cost.